PROFI-DOM — construction company +7 (707) 068-88-68
ENRUKZ

CANOPY WELDING IN ALMATY


from 12 000 tg.* PER m²
CALCULATE THE COST OF WELDING WORK

A canopy that won't sag under snow: frame made of 80×80 mm pipe rated for 120–150 kg/m², turnkey canopy 6×4 m — in 3–5 days, measurement free.

  • Frame for snow
    120–150 kg/m²
  • Canopy 6×4 m
    in 3–5 days
  • 3-year warranty
  • Measurement is free, price
    without extra charges

CANOPY WELDING IN ALMATY

from 12 000 tg.* PER m²

CALCULATE THE COST OF WELDING WORK

A canopy that won't sag under snow: frame made of 80×80 mm pipe rated for 120–150 kg/m², turnkey canopy 6×4 m — in 3–5 days, measurement free.

Frame for snow
120–150 kg/m²

Canopy 6×4 m
in 3–5 days

3-year warranty

Measurement is free, price
without extra charges

CANOPY WELDING IN ALMATY

from 12 000 tg.* PER m²

A canopy that won't sag under snow: frame made of 80×80 mm pipe rated for 120–150 kg/m², turnkey canopy 6×4 m — in 3–5 days, measurement free.

Frame for snow
120–150 kg/m²

Canopy 6×4 m
in 3–5 days

3-year warranty

Measurement is free, price
without extra charges

Types of welding
work we do

Fabrication of the canopy frame

Installation of the canopy roofing

Welding arched canopies

Reinforcement of existing canopies

Welding entrance canopies

Fabrication of terrace canopies

Welding canopies for a mangal

Installation of canopies for storing firewood

GET A CONSULTATIONWe will call you back within 3 minutes

Types of welding
work we do

Fabrication of the canopy frame

Installation of the canopy roofing

Welding arched canopies

Reinforcement of existing canopies

Installation of canopies for storing firewood

Fabrication of terrace canopies

Welding canopies for a mangal

Welding entrance canopies

GET A CONSULTATION

We will call you back within 3 minutes

Types of welding
work we do

Fabrication of the canopy frame

Installation of the canopy roofing

Welding arched canopies

Installation of canopies for storing firewood

Welding entrance canopies

Fabrication of terrace canopies

Welding canopies for a mangal

Reinforcement of existing canopies

We will call you back within 3 minutes

Cost of CANOPY WELDING
IN ALMATY

SERVICECOSTTIME
On-site measuring in Almatyfree of chargefrom 1 hour
Minimum order (call-out + work)from 25 000 ₸from 2 hours
Turnkey canopy with polycarbonate (per m²)from 12 000 ₸/m²from 3 days
Canopy frame without roofing 4×3 mfrom 96 000 ₸from 1 day
Canopy frame without roofing 6×4 mfrom 192 000 ₸from 2 days
Canopy for yard 4×3 m turnkey (polycarbonate)from 144 000 ₸from 3 days
Car canopy 6×4 m turnkey (polycarbonate)from 288 000 ₸from 3 days
Carport 6×4 m turnkey (profiled sheeting)from 336 000 ₸from 3 days
Installation of a canopy on the sitefrom 40 000 ₸from 1 day
Installation of polycarbonate on the framefrom 2 500 ₸/m²from 3 hours
Anti-corrosion treatment of seamsfrom 500 ₸/mfrom 1 hour
Painting the frame in RAL colour+5 000 ₸from 2 hours
Dismantling of the old canopy up to 6×4 mfrom 15 000 ₸from 2 hours
LEAVE A REQUESTWe will call you back within 3 minutes

Преимущества СВАРОЧНЫХ РАБОТ ОТ Profi‑Dom

Snow load calculation 150 kg/m²

We calculate the frame for a snow load of 120–150 kg/m² and record it in the specification

Welder-installer 11+ years

We weld canopies for cars, yards and entrances: single-slope, gable, arched and cantilever

Semi-automatic without slag

We weld the frame with 0,8 mm MIG/MAG wire — a slag-free seam, full penetration through the pipe thickness

Canopy turnkey in 3–5 days

1–2 day welding and painting in the workshop, 1 day installation; we concrete the posts to 60–80 cm

Official 3 year warranty

If a crack or pinhole appears in the seam — we re-weld for free, the warranty is specified in the contract

Transparent price in KZT

From 12 000 ₸/m² turnkey, measurement free — the estimate fixes all work without extra charges

LEAVE A REQUESTWe will call you back within 3 minutes

Преимущества СВАРОЧНЫХ РАБОТ ОТ Profi‑Dom

We calculate the frame for a snow load of 120–150 kg/m² and record it in the specification

Snow load calculation 150 kg/m²

We weld canopies for cars, yards and entrances: single-slope, gable, arched and cantilever

Welder-installer 11+ years

We weld the frame with 0,8 mm MIG/MAG wire — a slag-free seam, full penetration through the pipe thickness

Semi-automatic without slag

1–2 day welding and painting in the workshop, 1 day installation; we concrete the posts to 60–80 cm

Canopy turnkey in 3–5 days

If a crack or pinhole appears in the seam — we re-weld for free, the warranty is specified in the contract

Official 3 year warranty

From 12 000 ₸/m² turnkey, measurement free — the estimate fixes all work without extra charges

Transparent price in KZT

We will call you back within 3 minutes

Преимущества СВАРОЧНЫХ РАБОТ ОТ Profi‑Dom

We calculate the frame for a snow load of 120–150 kg/m² and record it in the specification

Snow load calculation 150 kg/m²

We weld canopies for cars, yards and entrances: single-slope, gable, arched and cantilever

Welder-installer 11+ years

We weld the frame with 0,8 mm MIG/MAG wire — a slag-free seam, full penetration through the pipe thickness

Semi-automatic without slag

1–2 day welding and painting in the workshop, 1 day installation; we concrete the posts to 60–80 cm

Canopy turnkey in 3–5 days

If a crack or pinhole appears in the seam — we re-weld for free, the warranty is specified in the contract

Official 3 year warranty

From 12 000 ₸/m² turnkey, measurement free — the estimate fixes all work without extra charges

Transparent price in KZT

We will call you back within 3 minutes

HOW WE WORK

LEAVE A REQUESTWe will call you back within 3 minutes
  1. 01.
    Discussion and estimate

    We consult by phone or WhatsApp and give a price guideline — from 12 000 ₸/m² turnkey.

  2. 02.
    Free measurement

    The surveyor checks the site slope, soil, and attachment points to the house so the canopy sits level.

  3. 03.
    Frame calculation

    We select the pipe cross-section for snow load of 120–150 kg/m² and the span, and fix the load in the specification.

  4. 04.
    Approval of the contract

    We fix in the contract a turnkey price, a term of 3–5 working days and a 3-year warranty on welds.

  5. 05.
    Welding in the workshop

    We cut the pipe on a band saw and weld the frame with a MIG/MAG semi-automatic machine in 1–2 days.

  6. 06.
    Anti-corrosion treatment and painting

    We prime the seams with GF-021 and paint the frame in two coats — the coating lasts 5–7 years.

  7. 07.
    Concreting of posts

    We concrete the posts to 60–80 cm; on heaving soil we reinforce and make a sand cushion.

  8. 08.
    Installation and roofing

    We assemble the canopy on site in 1 day and fasten polycarbonate or profiled sheeting with thermal washers.

Answer 5 questions and get an estimate accurate to 95%

Find out the cost and production time of a canopy in 1 minute

What kind of canopy do you need?

What's the approximate area?

What kind of roof do you want?

How will the canopy stand?

When do you plan to start?

One last step!

Enter your phone number so we can send you the estimate and reserve your gift!

+7

catalogue of completed welding work

Welding an arched canopy in the courtyard of a private house (Auezov district)Welding an arched canopy in the courtyard of a private house (Auezov district)
The customer needed a shelter for two cars from snow and sun. We welded a frame from 60x40 square tubing, covered it with 8 mm polycarbonate and made reinforced rafters.
280 000kzt
VIEW PROJECT
Installation of a wrought-iron canopy over the entrance area (Medeu district)Installation of a wrought-iron canopy over the entrance area (Medeu district)
The owner of a private house wanted an aesthetic and durable solution for the porch. We manufactured and installed a welded structure with wrought-iron elements and powder-coated enamel paint.
350 000kzt
VIEW PROJECT
Welding a canopy for a cafe on a summer veranda (Bostandyk district)Welding a canopy for a cafe on a summer veranda (Bostandyk district)
The owner of the establishment requested a prefabricated structure for the visitors' recreation area. We assembled a demountable frame from galvanised tube and stretched a tent material over it.
180 000kzt
VIEW PROJECT
Fabrication of a canopy for a utility block (Turksib district)Fabrication of a canopy for a utility block (Turksib district)
We needed to protect a building materials warehouse on the site from rain. We welded a single-slope structure from 40x20 profile, with corrugated sheet roofing.
150 000kzt
VIEW PROJECT

FIND OUT THE COST OF WELDING WORK FOR YOUR PROJECT

Leave a request and we will contact you within 3 minutes

+7
Privacy Policy

By clicking the button you agree to the terms of the

Or call us at

+7 (707) 068-88-68
Privacy Policy

FIND OUT THE COST OF WELDING WORK FOR YOUR PROJECT

Leave a request and we will contact you within 3 minutes

+7

By clicking the button you agree to the terms of the

Or call us at

+7 (707) 068-88-68
Privacy Policy

FIND OUT THE COST OF WELDING WORK FOR YOUR PROJECT

Leave a request and we will contact you within 3 minutes

+7

By clicking the button you agree to the terms of the

Or call us at

+7 (707) 068-88-68

Сварка навесов в Алматы от PROFI‑DOM: каркасы, кровля, цены

Welding canopies at PROFI-DOM — canopies for cars, yards and entrance areas: single-slope, gable, arched and cantilever. We weld the frame from profile pipe 60×40–100×100 mm with a MIG/MAG semi-automatic machine and design it for a snow load of 120–150 kg/m². Turnkey with polycarbonate — from 12 000 ₸/m², measurement in Almaty is free, warranty on welded seams — 3 years.

What canopies we weld — types, shapes, purpose

We will break down what welded canopies we make in the workshop — for a car, yard, terrace and entrance group, to make it easier to choose an option for your site.

Car and parking canopy — which one to choose

We weld carports from 80×80 mm profile pipe with truss spacing of 1,5 m — the structure withstands a layer of wet snow up to 150 kg/m² without sagging. The frame is calculated for a specific parking width: one car needs a span of 3,5 m, two — 6 m. In our projects we use pipe with a wall thickness of 2,5–3 mm and обязательно prime the seams before painting — this prevents corrosion at the joints. We install roofing from 8 mm thick polycarbonate or C21 — corrugated sheet: the first lets light through and does not darken the yard, the second is cheaper and dampens the noise of rain. It is better to make parking for two cars as a gable canopy 6 m wide — snow slides off it faster than from a single-slope one, and the load on the frame is distributed more evenly.

Canopy over the yard, terrace and recreation area

For the courtyard and terrace we offer canopies attached to the house on supports or cantilever ones without front posts — the second option is convenient if furniture or a grill stands under the canopy. The cantilever structure rests on embedded parts in the house wall and requires no corner columns, freeing up space. In our projects we use 60×40 mm tubing for purlins and a truss spacing of 1,2 m — this provides a strength margin for wind loads in open courtyards. An attached canopy to the house is fixed to embedded parts in the wall — this is more reliable than simply resting it on the facade, because it prevents the frame from shifting when the soil settles.

Single-pitch, gable or arched — which is better

We manufacture single-slope, gable, and arched canopies — the choice depends on the span width and roofing material: profnastil suits a pitched shape, polycarbonate suits an arched one. A single-slope canopy with a 10–15° slope is the most budget option; it is installed in a parking spot by the fence or over a gate, with minimal metal consumption. A gable canopy requires more material for the rafter system, but the snow load is distributed over two planes, and on spans from 5 m it is more reliable than a single-slope one. An arched canopy made of bent pipe is more expensive to manufacture, but snow does not linger on it — in Almaty conditions with frequent thaws this is a plus, because wet snow does not compact on the arch and slides off by itself.

Canopy over the entrance area and porch canopy

For the entrance area, we weld both compact canopies with an overhang of up to 2 m and full-sized canopies of 3–4 m — the second option protects the porch from slanting rain and extends the service life of the door, which does not get wet in a downpour. We make the canopy from a 40×20 mm pipe with cladding of monolithic polycarbonate 6 mm — it is lightweight, does not require powerful supports, and is attached directly to the wall with anchors. A full-sized canopy over the porch is mounted on two posts or welded to an existing concrete canopy. If there is already a concrete canopy above the door, it can be reinforced with a frame and extended — there is no need to demolish the old structure; it is enough to secure the new truss on top of the old slab.

How we weld the frame and calculate for snow and wind

Welding canopies starts with a sturdy frame based on calculation. Let's look at which tube we make the frame from, how we calculate the load and why semi-automatic welding produces a more reliable seam than electrode welding.

Which square tubing is needed for a canopy — 60×40, 80×80 or 100×100

For a carport of 6×4 m we use 80×80 mm profile pipe for support posts and 60×40 mm for trusses — this is sufficient for a snow load of 120–150 kg/m² for the region. On single-slope canopies over a yard with a span of up to 5 m, we take posts of 60×60, and the upper chord of the truss — 60×40 with braces made of 40×20. Cantilever canopies and entrance canopies with an overhang of up to 3 m require 60×40 for the cantilever beam and 40×20 for stiffening ribs. If the canopy is arched or gable with a span of 8–10 m, we reinforce the posts to 100×100, and assemble the truss from 80×80 along the lower chord and 60×40 along the upper. In the workshop, blanks are cut on a band saw at a precise angle for welding — without gaps in the joints. A 40×40 mm pipe is only suitable for canopies with an overhang of up to 2 m — on a carport it will sag in the very first winter.

Snow load calculation for Almaty — why it matters

We design the frame for a snow load of 120–150 kg/m² — this is the standard under the SP of the Republic of Kazakhstan, with a margin for wet snow, which weighs 2–3 times more than dry snow. On a gable canopy with a slope of 15°, snow stays on longer than on a single-slope canopy at 25°, so for such geometry we increase the truss cross-section by one step — for example, instead of 60×40 we use 80×40. In mountainous areas (Medeu, Kamenka) the actual load reaches 180 kg/m² due to frequent snowfall, and we additionally reinforce the posts with braces. If a welder says “by eye” and does not ask about snow — in 2–3 years the trusses will start to bend, especially on gable canopies with a low slope. On all projects we record the design load in the specification — so that you can check the strength margin before installation.

MIG/MAG semi-automatic welding — why we do not weld with an electrode

We weld the entire frame with a MIG/MAG semi-automatic welder — the seam comes out even, without slag, with penetration through the full thickness of the metal, which rules out cracks under load. 0,8 mm wire in a carbon dioxide environment gives a stable arc even on thin 40×20 — tube, so there is no overheating of the metal or deformation of the profile. Welding the frame with MMA electrodes takes 2–3 times longer, and after each pass the slag must be chipped off, hiding possible lack of penetration. The workshop has Kemppi and Svarog inverter semi-automatic welders — they hold the current steadily at metal thicknesses from 1,5 to 4 mm. We use MMA electrodes only on site, when embedded parts need to be welded to the wall of a house — for the frame it gives a rougher seam with a risk of lack of penetration.

Anti-corrosion treatment and painting of the frame

After welding we clean the welds, prime the frame with an alkyd-based anti-corrosion primer and paint it in two coats — this is enough for 5–7 years without corrosion in the conditions of an Almaty winter with de-icing agents. We apply GF-021 primer immediately after cleaning, while the metal has not yet become covered with an oxide film — this improves the adhesion of the paint to the square tube. We paint canopies over open parking areas with KhV-16 — enamel — it is resistant to ultraviolet light and temperature fluctuations from −30 to +40 °C, which is relevant for the local climate. We additionally treat the ends of the tubes with sealant and close them with plastic caps — this blocks moisture from getting inside the profile. If the welder has not treated the welds inside the tube — in 2–3 years rust will start from the inside, especially on square tube with open ends.

Canopy roofing — polycarbonate or corrugated sheet

Let us compare the two main roofing materials — polycarbonate and corrugated sheeting. We will work out which is better for a car canopy and which is better for a yard or terrace.

Cellular and solid polycarbonate — which is better for a canopy

We use 6–10 mm cellular polycarbonate for arched and pitched canopies — it is lighter than monolithic, transmits light and does not crack at temperature differences from −30 to +40 °C. The 8 mm thick cellular structure withstands snow load up to 160 kg/m² with a lathing pitch of 700 mm, which complies with standards for Almaty and the foothills; monolithic polycarbonate of the same thickness is 2–3 times heavier and more expensive, but absolutely transparent — it is installed on canopies and small forms up to 2 m², where visibility and hail resistance are important. You can order cellular polycarbonate with UV protection for 10 years from us — it does not yellow on the south side. On a large canopy, a monolithic sheet creates extra load on the frame and requires reinforcement of the trusses, which makes the structure more expensive by 20–30 %.

Corrugated sheet S8 and S21 — — which profile to choose

For the canopy roof we recommend corrugated sheet C21 — — it has a higher wave (21 mm), which provides rigidity over spans up to 1,5 m, and snow slides off it more easily than from C8. Profile C8 with a wave height of 8 mm is cheaper but suitable only for continuous lathing with a pitch of no more than 0,5 m — on typical trusses with a pitch of 1 m it "slaps" under wind gusts up to 25 m/s, typical of the Almaty foothills; the metal thickness of both profiles varies from 0,4 to 0,7 mm, and for a canopy 0,5 mm with a zinc coating of 140 g/m² is sufficient. In the workshop we weld a frame for corrugated sheet C21 with a truss pitch of 1,2 m — this is the optimal ratio of metal consumption and roof rigidity.

Which is better for a canopy — polycarbonate or corrugated sheeting

Polycarbonate transmits light and is suitable for canopies over a terrace or pool; corrugated sheet is for carports and utility blocks where opacity and sound insulation from rain are important. Cellular polycarbonate 8 mm diffuses up to 80 % of sunlight, creating soft partial shade — furniture does not fade under it and it does not glare, but in rain the sound of drops is clearly heard; C21 corrugated sheet with a polymer coating (pural or polyester) completely blocks light, dampens hail noise, and looks monolithic. If the canopy is attached to the house and there are windows underneath — polycarbonate is better, otherwise the room will be dark; for a detached canopy in the yard, corrugated sheet is more practical.

Cantilever canopies and complex shapes

Cantilever canopies without front supports — a solution for those who want free space under the canopy. We will explain when they are needed and how we calculate them.

Cantilever canopy — when it is needed and how it is built

We weld cantilever canopies with an overhang of up to 4 m without front supports — the frame is attached to the house wall through embedded parts, and the load is distributed to a reinforced truss and posts on both sides. For the cantilever we use profile pipe 80×80 mm on support posts and 60×40 mm on the truss, the spacing of embedded parts is no more than 60 cm. The weld on such units is reinforced with gussets made of 6 mm sheet, otherwise in a strong gust of wind the truss can be torn out of the wall. For a cantilever canopy over parking, we lay in a margin for snow load 30% — in Almaty this is about 160 kg/m² instead of the calculated 120. A cantilever canopy is more expensive than a regular one by 30–40% due to the reinforced frame, but if a car or a mangal stands under it — the absence of posts pays off with convenience.

Arched canopy — pipe bending and truss assembly

We bend arched canopies on a pipe bender from 60×40 mm profile pipe — we calculate the arch radius so that the polycarbonate does not crack when bent and snow rolls off without lingering. The minimum bend radius for a 60×40 — 1,5 m pipe, for arches over a pool 6 m long we use a truss spacing of no more than 1 m (otherwise the polycarbonate sags between the arches under snow) and 10 mm cellular polycarbonate — it withstands hail impacts up to 20 mm. Trusses are welded in a jig so that all arches are identical in radius: a deviation of more than 5 mm causes roof skew and water stagnation in the polycarbonate cells.

Canopy attached to the house — fixing specifics

We attach an attached canopy to the house wall through embedded parts on anchors — this prevents the frame from tearing off the facade under strong wind load. For brick walls we use Hilti chemical anchors with an embedment depth of 120 mm, for concrete — mechanical wedge anchors M12. The load from the truss is transferred to a support beam made of a 80×80 pipe, which is welded to the embedded plates — a weld with a leg of 6 mm runs along the entire perimeter of the plate. If the house wall is made of aerated concrete or shell rock — ordinary anchors do not hold, it is necessary to install through studs with plates on both sides.

Canopy price — per m², turnkey, frame separately

Let's break down canopy prices — per square metre, turnkey and for the frame alone. A canopy price consists of several components: we'll show what they are and how to avoid overpaying for unnecessary options.

How much does it cost to make a canopy at PROFI-DOM — prices per m² and turnkey

The price for manufacturing a canopy at PROFI-DOM is from 12 000 ₸/m² turnkey with polycarbonate and from 14 000 ₸/m² with corrugated sheet, including a 80×80 mm profile pipe for posts, 60×40 mm for trusses, 8 mm cellular polycarbonate or C21 0,5 mm corrugated sheet, concreting of each post to 60–80 cm with 10 mm rod reinforcement, anti-corrosion treatment and two-layer painting with primer enamel. The pipe cross-section is calculated for a snow load of 120–150 kg/m², and the concreting depth — for wind gusts up to 25 m/s in the Almaty region. The price per m² is convenient for quick comparison, but the final cost of a 6×4 m structure turnkey — from 288 000 ₸ — more accurately reflects the budget because it fixes all work and materials without hidden markups for roof complexity or cantilever overhang.

Price list for canopies — price table

Canopy / labourRoofUnitPrice from, ₸
Car canopy 6×4 m turnkeyCellular polycarbonate 8 mmcanopy288 000
Car canopy 6×4 m turnkeyCorrugated sheet C21canopy336 000
Yard canopy 4×3 m turnkeyCellular polycarbonate 6 mmcanopy144 000
Canopy frame without roofing 6×4 m—frame192 000
Canopy frame without roofing 4×3 m—frame96 000
Installation of a canopy on the plot (standalone)—labour40 000
On-site measuring in Almaty—servicefree of charge

Ordering the frame separately is advantageous if you want to buy and lay polycarbonate or corrugated sheet yourself — saving up to 15–20% by omitting the roofing material and the work of installing it.

What the turnkey price includes — frame, roofing, installation

В цену под ключ от PROFI‑DOM входит профтруба расчётного сечения, сварка каркаса полуавтоматом, антикор и покраска (держит 5–7 лет на перепадах от -30 до +40 °C), кровельный материал, бетонирование стоек М200 на 60–80 см с армированием 10 мм и монтаж на участке — вы получаете готовый навес без доплат. Заказ «под ключ» выгоднее поэтапного, потому что мы закладываем скидку на объём работ — отдельно каркас + кровля + монтаж выйдут на 10–15% дороже, причём разница растёт с увеличением площади из-за повторного выезда бригады для каждого этапа.

Additional services — reinforcement, dismantling, RAL painting

  • Reinforcement of the frame for heavy roofing: replacement of truss pipe from 60×40 to 80×40 mm for seam roofing or metal tiles — +20% added to the frame cost.
  • Dismantling of an old canopy: disassembly, removal of scrap metal and debris — from 15 000 ₸ per structure up to 6×4 m.
  • Painting in any RAL colour: two-layer coating with matt enamel — +5 000 KZT on top of the total cost.
  • Increasing the cantilever overhang to 4 m: an additional stiffening rib made of 40×40 mm pipe — +15% to the cost of the cantilever canopy.
  • Anti-corrosion treatment of the base of the posts: bitumen mastic up to 30 cm from the ground — +2 000 ₸ per canopy.

Painting in RAL makes sense if the canopy is in a prominent place at the entrance — the standard grey or green colour may not fit the house facade, and ordering a custom shade costs only 5 000 KZT with a total budget from 144 000 KZT.

Measuring, fabrication and on-site installation

Turnkey canopy welding includes measurement, fabrication in the workshop and installation on site. We will discuss whether a foundation is needed for the posts, how many days the frame is welded and what guarantees are given for welded seams.

On-site measuring — what we inspect and why

We provide free measurement visits in Almaty — the surveyor examines the soil type (loam or sand), the distance to the fence and the house facade, the slope of the plot and the attachment points to the wall in order to calculate the frame precisely for your plot. On site, he checks the height difference with a laser level: on a standard six-hundred-square-meter plot in the Alatau district, the difference reaches 15–20 cm, and if it is not taken into account, one side of the canopy will be lower than the other. He also records where the support posts will go — to avoid hitting underground utilities (sewer, water supply). If the surveyor did not come and asks you to send photos — there is a high risk that the canopy will not fit the site: the height difference on the plot may be 10–15 cm, and this is not visible in a photo.

Is a foundation needed under a canopy — concreting the posts

Under the canopy, we concrete the support posts to a depth of 60–80 cm — this method holds the structure during soil heaving in winter. For a single-slope canopy of 3×6 meters, four posts made of 60×60 mm pipe with concrete "shoes" of 30×30×50 cm are sufficient — this replaces a full strip foundation and saves up to 40% of the installation budget. On heaving soils (loam in the Aksai-2 microdistrict), we additionally reinforce the concrete with 10 mm rebar and make a sand cushion of 20 cm under each post. If you simply bury the posts without concrete, after 2–3 years frost will start to push them out, the canopy will skew, and the roof will warp.

Lead times for manufacturing and installing a turnkey canopy

Turnkey canopy manufacturing takes 3–5 working days — 1–2 days for welding the frame in the workshop and painting, 1 day for on-site installation with roof fixing. A standard single-slope canopy 3×6 meters made of 60×60 mm pipe with polycarbonate is welded in one day, a gable one for 4×8 meters — in two, because the rafter system is more complex and there are more seams. In season (April–October) the installation queue can be up to 2 weeks — this should be taken into account if the canopy is needed before the first snowfall.

Warranty on welded seams and the canopy structure

We give a 3-year warranty on welded seams and the canopy structure from the date of installation — if a crack appears in the seam or a fistula, deformation of the frame or subsidence of the posts, we fix it free of charge. The warranty does not cover mechanical damage (a blow from a branch, a car hitting it) or corrosion of seams if you painted the frame yourself with the wrong paint — for example, ordinary NC enamel instead of anti-rust primer enamel.

Conclusion

We have gathered the main criteria for choosing a canopy — from the type of structure to the final price. These five points will help you avoid mistakes when ordering.

Key takeaways on choosing and ordering a canopy

  • The type of canopy depends on the task: for a car — gable or arched, for a yard — cantilever or attached, for an entrance — a compact canopy.
  • The frame should be made of 80×80 mm square tubing for a carport and 60×40 mm for small structures — the section is calculated for the snow load of your region.
  • Roofing: polycarbonate is suitable for light-transmitting canopies (terrace, pool), corrugated sheet — for opaque ones (car, utility block).
  • The turnkey price includes everything: the frame, roofing, concreting and installation — ordering “turnkey” is 10–15% cheaper than doing it in stages.
  • Before ordering, a surveyor needs to visit the site — without it, an accurate calculation of the frame and cost is impossible.

About the author

Ruslan Akhmetov

Welder-installer of canopies at the PROFI-DOM workshop in Almaty. Frames made of square tube: canopies for cars, yards and entrance areas, single- and gable, arched, cantilever; roofing in polycarbonate and corrugated sheet.

More than 11 years in the manufacture and installation of canopies; frame calculation for Almaty's snow load, full welding of truss joints, anti-corrosion treatment and installation by level.

Frequently asked questions
ABOUT WELDING CANOPIES IN ALMATY

How much does canopy welding cost in Almaty?
Turnkey canopy — from 12 000 ₸/m² with polycarbonate and from 14 000 ₸/m² with profiled sheeting. Turnkey car canopy 6×4 m — from 288 000 ₸, frame without roofing 4×3 m — from 96 000 ₸.
What are the fabrication and installation times for a canopy?
We make a turnkey canopy in 3–5 working days: 1–2 days for welding and painting in the workshop, 1 day for installation. In season (April–October) the installation queue can be up to 2 weeks.
Which canopy is better: polycarbonate or corrugated sheeting?
Polycarbonate transmits light better and is suitable for recreation areas, while corrugated sheet protects more reliably from precipitation and is more durable. The choice depends on your needs: corrugated sheet is more often chosen for parking, and polycarbonate for a terrace.
Do you provide on-site measuring in Almaty?
Yes, we provide free on-site measurements in Almaty. A specialist will arrive at a time convenient for you to assess the site and discuss details.
Do you provide a warranty on welding work?
We give a 3-year warranty on welded seams and the canopy frame: if a crack appears in a seam or a post sags, we fix it free of charge provided it is used correctly.
What common problems arise when welding canopies?
The most common problem is an incorrect load calculation, which can cause the structure to warp. In Almaty it is also important to take the wind load into account, so we reinforce the frame with additional stiffeners.
Phone:+7 (707) 068-88-68Our address:Almaty, Makataev St., 47, office 325 (Partner Business Centre)Daily: 9:00–21:00 (by appointment)